ATT-Tactical™

A True Water-Environment Ballistic Protective Vest A TRUE MARITIME OPERATOR'S BALLISTIC FLOTATION VEST SYSTEM

If your team operates anywhere near or on the water, then this is YOUR tactical vest. Constructed of the finest materials available, our M.B.V. is designed and intended for water-borne operators. DON'T LET THE WEIGHT OF YOUR WATER-LOGGED BALLISTIC VEST DRAG YOU DOWN. Our DX Ballistic material (Dyneema® & Twaron®) is impervious to salt water degradation. The panels meet or exceed the NIJ 0101.06 requirements. The material's fibers do not absorb water (24 hour salt water emersion) This system meets or exceeds the FBI / DEA Test Protocols.
Level IIIA Performance: Aerial Density: 1.05 psf Panel Thickness: .23" 9mm V50/V0: 1876fps / 21mm .44mag V50/V0: 1656fps / 38mm 9mmWin 127gr SXT+P+	The vest is a true break-away design with a single protected disengagement pull-tab
Special Threat V50 Performance: Winchester Ranger 9mm 127grain SXT +P+: 1834fps Speer Gold Dot .357Sig 125 grain: 1794fps FNH FN5.7x28mm (SS195): 2232fps	The vest separates at one shoulder and at the rear cummerbund. Escape from your vest if you've fallen overboard.
In addition to the above: this panel meets the following US Military Fragmentation Requirements for WET V50 RCC 2gr: 2725fps RCC 4gr: 2429fps RCC 16gr: 1994fps RCC 64gr: 1697fps MBV without rifle plates MSLP $ 3247.50 As low as $1800 each in volume	The ballistic panels are sealed inside a water-proof bag and adds no weight to the operator.
Level III++ Rifle Plate These Ultra-light plates are certified to protect against rifle fire as "In Conjunction" - Full protection up to level three-plus threats when used with a Level IIIA vest, and will defeat multiple spaced hits as per NIJ standards of: 7.62 mm NATO USM. BALL M80 150 grains projectile @ 2750 ft/sec 5.56 mm NATO USM. BALL M855 62 grains projectile @ 3050 ft/sec 5.56 mm NATO USM. BALL M193 55 grains projectile @ 3250 ft/sec and/or lesser threats. Will defeat single hits of higher threats. UHMWPE ICW Rifle Plate MSLP $950.95 As low as $500 each in volume	UHMWPE = Ultra High Molecular Weight Polyethylene Multi Curved Spectra with Alumina. 10 X 12 Inch Operator Cuts w/wear resistant nylon cover
If you need positive flotation where you may find yourself knocked overboard while wearing a fully-loaded tactical vest (magazines, gas mask, flash-bangs, radio, Level IV Rifle Pates, etc.) we can now offer the TFSS (Tactical Flotation Support System) as an up-fit to our neutral-buoyant Maritime Ballistic Vest (MBV).
AUTO-TFSS For Tactical Ballistic Vests The Tactical Flotation Support System (Patent Pending) ™ AUTO-TFSS, designed by PECI Flotation, L.L.C, is an inflatable aid-to-flotation device specifically designed for covert war fighters, combat swimmers, and/or maritime airborne operations personnel. It can also be used with the Helicopter Aircrew Breathing Device (HABD) during egress from a submerged vessel of any type. The AUTO-TFSS was designed to provide 45lbs positive buoyancy in seawater at a depth of 33 ft., 57lbs of positive flotation at a depth of 15 ft., and 80lbs of flotation on the surface, allowing today’s war fighter a maximum load-out equipment. If your ship-boarding team gets knocked or shoved overboard, that now can survive even if weighed down with a 30lb tactical vest and sidearm.
Each AUTO-TFSS system consists of one each independent left and right hand units, which can be mounted on a belt. Each unit includes a welded flotation bladder, an inflation system, a pouch closure system, a pouch, and a firing handle. The bladder is a reusable welded fabric enclosure that deploys under the arm and is readily collapsed and stowed for future use. The inflation system utilizes a manually actuated CO2 cartridge for primary inflation and an oral inflation tube for secondary inflation. The AUTO-TFSS pouch uses a unique Grommet, Loop, and Pin (GLP)closure system design that combines positive closure of the pouch with space efficient packing. This method prevents accidental pouch opening and allows for the smallest unit size when fully packed (approx 6.5" x 2.7x 2.25"). A durable Cordura flap to further protect against damage and inadvertent actuation covers the entire closure mechanism. The system attaches to a MOLLE cummerbund on the Tactical Vest or to a MOLLE Battle Belt
The AUTO-TFSS pouch contains and protects the bladder, inflation system, and closure system. It includes a waist belt loop and clip loops to secure the pouch to the webbing belt. The firing handle attaches to the outside of the pouch and uses color-coded beads to help distinguish left and right hand units. The handle serves to release the closure system and actuate the CO2 inflation system. To manually actuate a AUTO-TFSS unit, the user pulls upward on the firing handle. This motion initiates two sequential actions. First the pouch closure pins are released, allowing the pouches to open freely. Second the manual inflator lever is actuated, causing the firing pin to puncture the seal on thCO2 cartridges to release the gas and completely fill the bladder. Should the CO2 inflation system fail to operate, the bladder is filled through an inflation tube. This is accomplished by depressing the Oralock valve, the breathing into the tube. Gas is released from the AUTO-TFSS bladder by pressing downward on the Oralock valve and forcing the air out the oral inflation tube. Once all of the gas is evacuated from the bladder, the CO2 cartridges are replaced, maintenance is performed, and the units are repacked for future use. This system adds $500 to our MBV cost.

Number of Unique Visitors

A True Water-Environment Ballistic Protective Vest